Anti-Mould Paint

Filter

Search
Accepted Cards

Here to help01509 216 323

01509 216 323

Download our free "A Homeowners Guide to Condensation in your Property"

Anti Condensation Paint (2.5L)

acs_anticond

£ 34.80 (Inc VAT)
£ 29.00 (excl VAT)

+

Specifications



Colour: White
Size: 2.5 litre
Finish: Matt
Coverage: 4-6m²/litre per coat (2-3 coats are recommended)
UK Delivery: £5.00 inc VAT

ANTI-CONDENSATION PAINT

A single-pack advanced waterborne, condensation control coating based on acrylated vinyl acetate, with natural earth minerals and non-toxic pigments.

USES

This anti condensation paint is suitable for commercial, industrial and domestic use for reducing the incidence of condensation on ceilings and walls. The paint works in two ways; initially providing an insulating layer to keep the surface temperature above the dewpoint, delaying the onset of surface condensation. Secondly, at times of high humidity by absorbing atmospheric moisture, reducing droplet formation and releasing the trapped moisture as vapour when the relative humidity drops.

Can be used in hospitals, schools, farms, breweries, offices, factories and domestic properties, in kitchens, shower rooms, animal-rearing sheds and other areas where condensation is a problem or causes spoilage.

This product contains an 'in-can biocide' to protect the applied film from fungal growth.

TECHNICAL PROPERTIES

Drying Times @ 20°C

Touch:                                                                              1 hour

Hard:                                                                                2-3 hours

Re-Coat:                                                                           2-3 hours

Full cure – return to service:                                               24-hours (depending on conditions)    

Thinners/Clean up:                                                            Water

GENERAL SURFACE PREPARATION

Ensure all surfaces are clean, dry and free of oil, grease and wax. Fill all holes with a suitable filler or decorators caulk and rub down to a fine finish. Any existing coatings should be in good condition and well adhered to the surface. Rub down and loose or flaking paintwork back to a sound, firm line. Remove any loose wallpaper.

Glossy surfaces or oil based finishes: should be lightly abraded with aluminium oxide paper, washed with a mild detergent solution, rinsed with clean water and allowed to dry. 

Porous masonry and new plaster: should be allowed to dry thoroughly. Apply one coat of an Acrylic Surface Sealer and allow to dry. This should also be used on un-painted Artex or similar textured

APPLICATION

Do not thin. Apply by brush or roller.

Stir or shake the contents well, before use. Dampen brush or roller with a little water, load well, apply liberally and lay-off early. Do not overspread and avoid coating surfaces that are partly dry. Always work to a wet edge. Re-coating is recommended after 2-3 hours, although this time can be reduced in good drying conditions to 1 or 2 hours.

Apply 2 or 3 coats at 4-6m2/litre per coat, allowing sufficient time for the initial coat to dry before applying the subsequent ones. Subsequent coats will appear to dry more quickly due to the adsorbent effect of the previous coats. In areas of very high humidity, further applications may be required.

The product will require periods of low humidity to allow any trapped water to evaporate from the coating, especially in areas of constant or very high humidity.                                                 

STORAGE

Store in dry, frost-free conditions. Ensure strict stock rotation is observed.

LIMITATIONS OF USE

Allow good ventilation in the working area to aid drying. Do not apply if the RH exceeds 85% or if the surface is less than 3°C above the dewpoint. Do not apply directly to ferrous metals. Not normally recommended for exterior use.

Product must be allowed to dry thoroughly before the area is returned to service. Therefore we recommend that showers etc are not used for a minimum of 24 hours after application.

This paint has a relatively hard coating and may be used on walls provided they are not subjected to wear or frequent washing. Some dirt pick-up may be noticed which can be removed by gentle wiping with a damp cloth. However surfaces subject to a high degree of soiling may retain dirt.

If used on walls, the product may be over-painted with Antimould Emulsion to provide a more dirt and wear resistant finish, However this will degrade the ability of the coating to adsorb moisture, although it will still provide some of its thermal insulation qualities.

Any person proposing to use this product should make arrangements to assess the suitability for application prior to commencing work. 

There are basic measures property owners can take, which will help keep mould and condensation to a minimum and this paint will compliment these practical points.

Ensure rooms are always warm and properly ventilated. Maintain some background heat throughout the day.
Provide good levels of natural or mechanical ventilation in susceptible areas such as bathrooms, shower rooms and kitchens.
Improve internal or external wall insulation.
On solid walls, consider the use of masonry water repellents to reduce water uptake and the subsequent drop in thermal insulation caused when walls are wet.
Vent tumble driers to the outside air and, when possible, do not dry clothes over radiators. Put lids on saucepans and close doors on rooms where large amounts of condensation are created.
 

PACK SIZE(S)

2.5litre HDPE Paintainer

This information is given in good faith and is based on the best of current knowledge through use and experience. However all recommendations are given without warranty or guarantee as conditions of use lie outside our control. Customers are advised that all technical information is under constant review and changes may occur without notice

Downloadable Datasheets

PDF  

Need some advice? Call 01509 216 323

Follow Us On


Like us on FacebookFollow us on Twitter

Technical Support


Like Us

01509 216 323
This email address is being protected from spambots. You need JavaScript enabled to view it.

Delivery Info


Like Us

We offer next day
UK Delivery
(standard delivery £5.00)


Restoration UK Logo

Restoration UK Ltd
Unit 3, 18 Hanford Way
Loughborough, Leicestershire
LE11 1LS

01509 216323
This email address is being protected from spambots. You need JavaScript enabled to view it.